cleaning Rubber Tile and Sheet Flooring
Rubber Tile and Sheet Flooring
Products
- Architectural SD Rubber
- Eclipse Electrically Conductive EC – and GF (glue free) – Rubber
- Eclipse Glue-Free (GF) Rubber
- StatLock Interlocking Static Dissipative (SD) Rubber Tiles
- Voltage Protection Matting for Electrical Safety
Information
- Advantages of Electrically Conductive (EC) Rubber
- Don't Choose Your Floor Until You Understand The Role of Footwear
- Seam Welding for Cleanrooms
Installation, Cleaning, Sustainability
Cleaning Instructions
EclipseEC Rubber floor covering is designed to retain its appearance with a minimal amount of cleaning and provide slip resistance and exceptional wearability. Eclipse Rubber flooring never needs waxes or coatings. This eliminates the downtimes associated with the waxing/stripping/waxing cycle necessary with many other floor coverings.
General Precautions
- Do not apply any hard coatings to StaticWorx® ESD Rubber Flooring.
- Never use grit brushes or black, green, or blue pads.
- For regular maintenance, self-contained automatic scrubbing machines may be used for large areas (white pad only.)
- Pick up spills right away, if possible.
- For stairs and small areas, special equipment is available from Lever Industrial.
- Be sure to maintain a good walk-off area in the entrance(s) of your facility. Prevent as much dirt from entering the building as possible. Walk-off mats should be used to wipe dirt and grit from shoes and prevent it from being tracked into the building. The walk-off mats should be cleaned at regular intervals so that they can properly fulfill the task they are intended to do.
Initial Cleaning After Installation
After finishing interior building construction, floor coverings usually require a thorough cleaning. No sealers are required for Architectural ESD Rubber tile. Initial cleaning procedures should not be performed within the first 72 hours after installation.
Procedure
- Totally sweep or vacuum area to be cleaned.
- Apply a diluted pH neutral cleaner such as StaticWorx Triboshield to the floor.
- Let solution act for 5-10 minutes. Important: Do not allow solution to dry.
- Scrub area with a single disc machine (150-300 rpm) and soft nylon brush or white pad.
- Remove (wet vacuum) residue.
- Rinse with clear water and remove.
- Allow floor to thoroughly dry (1-2 hours).
- Dry buff floor with single disc rotary buffing machine and soft nylon brush or white pad (not to exceed 300 rpm). Do not heel machine.
Regular Cleaning
Floors subject to heavier traffic will require more frequent interim care than low traffic areas.
daily cleaning
- Sweep with a clean broom or brush to remove dust and dirt.
- To remove light soils, spot clean with a neutral pH cleaner such as Triboshield cleaner.
Interim Maintenance (1-5 times a week)
- Sweep with a clean broom or brush to remove dust and dirt.
- To remove light soils, spot clean with a neutral pH cleaner such as Triboshield cleaner.
Stain Removal
Most stains can be removed with common solvents. To remove dried iodine-based spills such as Betadine, use a cleaner such as Butcher’s “Speedball 2000.” Scuffs and black heel marks can be easily removed by spot cleaning with a neutral pH cleaner such as Triboshield cleaner.
Note: Never use wax strippers or high alkaline liquids on EclipseEC Rubber or Harmony SD Rubber.
Waxes/High Shine
All StaticWorx ESD Rubber Flooring features a built in dirt repellent, which makes it unnecessary to apply wax coatings to protect the floor. Wax coatings are not recommended for antistatic flooring. StaticWorx Spray Buff may be used in high traffic areas.
More Downloads
Get in Touch
The form below will help us better understand your needs and get you as quickly as possible to the right person. We look forward to helping you solve your static problem!
You can expect a response within 24 hours. For faster service, please give us a call: 617-923-2000
StaticWorx high-performance static-control floors protect electronic components, explosives, and high-speed computers from damage caused by static electricity. ESD flooring is part of a system. Choices should always be based on objective, researched evidence. When you partner with us, we look at all possible items that may need to integrate with the floor, and, focusing on your goals and objectives, help you find the right floor for your application.
Flooring Products
We accept these major credit cards.
Get in Touch
East Coast: 617-923-2000
Email: [email protected]
“I’m so glad we were able to find an attractive solution that didn’t leave us with some run-of-the-mill ugly disaster.”
Share This
subscribe to newsletter
Sign up for our newsletter and occasional updates.
The FAA has updated its standard for facilities and electronic equipment. StaticWorx meets all requirements for ESD flooring.
Flooring Products
We accept these major credit cards.
“I’m so glad we were able to find an attractive solution that didn’t leave us with some run-of-the-mill ugly disaster.”
Share This
Get in Touch
East Coast: 617-923-2000
Email: [email protected]
subscribe to newsletter
Sign up for our newsletter and occasional updates.
The FAA has updated its standard for facilities and electronic equipment. StaticWorx meets all requirements for ESD flooring.
Flooring Products
We accept these major credit cards.
Get in Touch
East Coast: 617-923-2000
Email: [email protected]
“I’m so glad we were able to find an attractive solution that didn’t leave us with some run-of-the-mill ugly disaster.”
Share This
subscribe to newsletter
Sign up for our newsletter and occasional updates.
The FAA has updated its standard for facilities and electronic equipment. StaticWorx meets all requirements for ESD flooring.
This site is protected by copyright and trademark laws under both United States and International law.
All rights reserved. © 2008-2022, StaticWorx® Grounded Solutions™. Privacy Policy
